WALL THIN SOUNDPROOFING SET WITH ECO SLAB SLIM

Soundproof electric socket SoundBOX is used for installing electric sockets(outlets), electric switcher into soundproofing schemes. Minimal thickness allows you to install soundproof electric socket even in the thinnest soundproofing schemes.

Soundproof electric socket is made of high strength polymer, that provides long service life and high values of soundproofing.

Soundproof electric socket SoundBOX is used for installing electric sockets(outlets), electric switcher into soundproofing schemes. Minimal thickness allows you to install soundproof electric socket even in the thinnest soundproofing schemes.

Soundproof electric socket is made of high strength polymer, that provides long service life and high values of soundproofing.

Using MaxForte-ShumoIzol under the screed is a standard floor soundproofing solution for new buildings where the sand-concrete screed is required. The increase in floor soundproofing equal to 27 dB guarantees the compliance with all requirements of the Building Codes and Regulations (SNiP) “Noise protection” including those for class A “Luxury Housing”! In addition to superior soundproofing, MaxForte-ShumoIzol also provides high-quality waterproofing of the premises.

Basic soundproofing of apartment floors. MaxForte-ShumoIzol rolls should be spread over a pre-leveled floor and then covered with two layers of gypsum plasterboard sheets. For a dry screed, the plywood sheets or the ready-made components of KNAUF-Superpol system can also be used. The advantages of this option are the fast mounting (no wet works required) and the small thickness of the whole structure which is particularly important for low ceiling bearing-wall houses. This design provides the impact noise reduction of as down as 20 dB!

This is a second thin option of ceiling soundproofing. In this option, the impact noise is isolated by the VibroStop Standart vibration insulating hangers, and the sound is absorbed by the 80 kg/m³ MaxForte-ECOslabs (thin slabs of 3 cm in thickness). This structure is based on the 60/27 mm KNAUF profile providing a smooth ceiling surface. After the ceiling is mounted, it is ready for finishing; no additional levelling should be required. The above structure is designed for complete isolation against the domestic noises – like voices, TV, footsteps and trampling – in the apartment buildings. Noise reduction down to 14 dB.

This thinnest option of ceiling soundproofing comprises the drywall and the profiles. It is an ideal solution for the apartments with low ceilings where every centimeter counts. This structure is based on the 60/27 mm KNAUF profile providing a smooth ceiling surface immediately. The rolls of MaxForte-SoundPRO – a state-of-the-art composite material which is only 12 mm in thickness – are applied for sound insulation. This material should be attached to the ceiling with ordinary expansion anchors. At the points where the frame is attached to the concrete, the SoundPRO is compressed and due to this acts as a damper reducing the vibration. At the rest area of the ceiling, the material absorbs the sound waves due to its fibrous structure. Thanks to the enhanced flexibility of SoundPRO, it can be used as sound insulation even for complex-shaped ceilings (with pipes, wiring, or height difference). 3-4 times reduction of noise from the upstairs (down to 12-14 dB).

A standard option of the floor structures soundproofing suitable for almost any housing (with some variations) is as follows: at least three layers (150 mm) of the sound-absorbing 60 kg/m³ MaxForte-ECOslabs should be mounted between the beams to isolate the airborne noise (like voices, shouts, TV, radio), and the vibration dampers (damping pads) should be mounted on the beams to isolate the impact noise (creaks, tramping, footsteps, falling objects). In addition, the massive sheet materials (like plywood, OSB, gypsum plasterboard) should be used instead of the rough floor boards in order to increase the tightness and sound insulation of the floor structure.

This is a second thin option of ceiling soundproofing. In this option, the impact noise is isolated by the VibroStop Standart vibration insulating hangers, and the sound is absorbed by the 80 kg/m³ MaxForte-ECOslabs (thin slabs of 3 cm in thickness). This structure is based on the 60/27 mm KNAUF profile providing a smooth ceiling surface. After the ceiling is mounted, it is ready for finishing; no additional levelling should be required. The above structure is designed for complete isolation against the domestic noises – like voices, TV, footsteps and trampling – in the apartment buildings. Noise reduction down to 14 dB.